shaping fork tines
Printed From: Nasgaweb
Category: Nasgaweb Forums
Forum Name: Throwing Only
Forum Discription: This forum is only for discussions that relate to throwing such as results, technique, and records.
URL: http://www.nasgaweb.com/forum/forum_posts.asp?TID=11193
Printed Date: 3/26/26 at 10:26pm
Software Version: Web Wiz Forums 10.11 - http://www.webwizforums.com
Topic: shaping fork tines
Posted By: Alan H
Subject: shaping fork tines
Date Posted: 9/10/10 at 7:09am
|
OK, I've got the fork, I've removed the extra tines and now I need to make the two remaining tines nice and shiny and smooth and pointy. There's no way I can do this with a file. The tines are way too hard, I'll be at it every day for three weeks. So how do y'all get the initial shape and taper in the fork tines? Once I've got a nice shape I'll go after it with a couple of grades of emery paper to make 'em smooth. ------------- Alan Hebert Geezer-In-Training |
Replies:
Posted By: rwilson
Date Posted: 9/10/10 at 8:32am
|
I used a 4" grinding wheel for the rough shaping, then swiched up to the Dremel tool with a small grindstone, and finally sandpaper. It took a while, but worked fine. ------------- -Rich W. ----------------------------- |
Posted By: Old Dude
Date Posted: 9/11/10 at 11:06am
|
I clamped the fork to my outdoor work bench and then attacked the tines with an angle grinder. The tines on your fork most probably have a diamond profile and you'll want to work the profile down until it's round. Don't go crazy with the grinder, just remove a little at a time. Keep the grinder moving at all times so you don't dig out more than you should. After that, it's all about the flat file. It shouldn't take very long to do if your fork is clamped solidly. Draw the file along the length of the tine. Doesn't matter if the file is flat and the tines are curved as the edge of the file cuts just as well as the flat. Once you've got the tines all nice and shiny, hit them with progressively finer grits of wet-or-dry paper. Don't use water or anything else. Dry is fine. I stopped at 600 grit. Last thing is to apply some WD-40 to the tines to make them slick. Re-apply as needed. ------------- Over Fork Over |
Posted By: Alan H
Date Posted: 9/11/10 at 2:20pm
|
I have a dremel, but unfortunately don't have a grinder or angle grinder. However, a quick visit to 5th. Avenue Rental will give me a grinder for a saturday afternoon for a few bucks and that will probably do it.
------------- Alan Hebert Geezer-In-Training |
Posted By: Old Dude
Date Posted: 9/11/10 at 2:45pm
|
...or $35 and trip to Lowes or Home Depot and you will have one for life. Caught a sale on my Makita and paid only $29 for it. ------------- Over Fork Over |
Posted By: Tommi
Date Posted: 9/12/10 at 12:44pm
|
A grinder to remove paint and make sure it doesn't have big bumps in it. Then use sandpaper. An AWESOME addition is to use a flapper wheel and terry cloth. It sounds silly but it works wonders. ------------- Tommi.Kitchens. |
Posted By: WALLY.OLECIK
Date Posted: 9/12/10 at 8:05pm
|
OR - just put a few coats of paint on the tines and then start your smoothing. The paint will fill in the low places and the tines will then be easier to get smooth!
------------- 16lb-hammer(at)sshga.org "Try not. Do or do not. There is no 'try!'" Yoda |
Posted By: RandyM
Date Posted: 9/15/10 at 12:40am
|
Do the tines need to be round? I finaly found an older pitchfork with thin tines and don't want to mess it up. They are to hard to find around here unless you want to pay a high price.
Randy |
Posted By: Old Dude
Date Posted: 9/15/10 at 4:57am
|
I don't think the profile matters that much on an older thin-tined fork. The five tined barley forks available on the West Coast have relatively thick tines and removing the diamond profile brings them more in line with the older style tines. As long as the bag slides off the tines with little or no hesitation and the fork "rings" after the toss, you'll be fine. ------------- Over Fork Over |
Posted By: RandyM
Date Posted: 9/15/10 at 5:03am
| Thanks for the advice. |
Posted By: Soul Eater
Date Posted: 9/22/10 at 5:01am
|
Go to harbor Freight pick up a cheap angle grinder. Dremels aren't made for
heavy metal grinding you'll just screw it up.The newer tines that are on union forks have a great deal of casting marks, you will spend some time(1 - 3 hrs depending on what you want) knocking those down, I like a round rat tail file which works well then when the metal feels smooth a consistant take a scotch brite & fine sanding wheel in a drill (not cordless) and that will getit to a point that is really smooth. |
Posted By: weaselking
Date Posted: 9/22/10 at 5:40am
yep yep yep. Can't even imagine spending 2-3 hrs w/ an angle grinder. We're not building clocks. ------------- We can evade reality, but we cannot evade the consequences of evading reality. - Ayn Rand |
Old Dude wrote:Posted By: Soul Eater
Date Posted: 9/22/10 at 6:00am
|
there is less work on the older thiner fork tines than there is on the new
ones. Basically knock the rust off with some navel jelly and some steel wool and clean them up and you should be ready to go. |
Posted By: Old Dude
Date Posted: 9/26/10 at 6:31pm
|
The Fork Master has spoken. This is my fork. There are many like it but this one is mine. My fork is my best friend. It is my life. I must master it as I master my life. My fork, without me, is useless. Without my fork, I am useless... ------------- Over Fork Over |